• Scope Descriptions
• Supplemental Information
• How to Request a Scope Ruling

Contact Information

• Enforcement and Compliance
  Customs Liaison Unit
  (202) 482-0984
  

• International Trade Administration

Carbon And Certain Alloy Steel Wire Rod from Trinidad and Tobago [ A-274-804 ]

Scope Description

The merchandise subject to this order is certain hot-rolled products of carbon steel and alloy steel, in coils, of approximately round cross section, 5.00 mm or more, but less than 19.00 mm, in solid cross-sectional diameter.

Specifically excluded are steel products possessing the above-noted physical characteristics and meeting the HTSUS definitions for (a) stainless steel; (b) tool steel; c) high nickel steel; (d) ball bearing steel; and (e) concrete reinforcing bars and rods. Also excluded are (f) free machining steel products (i.e., products that contain by weight one or more of the following elements: 0.03 percent or more of lead, 0.05 percent or more of bismuth, 0.08 percent or more of sulfur, more than 0.04 percent of phosphorus, more than 0.05 percent of selenium, or more than 0.01 percent of tellurium).

Also excluded from the scope are 1080 grade tire cord quality wire rod and 1080 grade tire bead quality wire rod. This grade 1080 tire cord quality rod is defined as: (i) grade 1080 tire cord quality wire rod measuring 5.0 mm or more but not more than 6.0 mm in cross-sectional diameter; (ii) with an average partial decarburization of no more than 70 microns in depth (maximum individual 200 microns); (iii) having no non-deformable inclusions greater than 20 microns and no deformable inclusions greater than 35 microns; (iv) having a carbon segregation per heat average of 3.0 or better using European Method NFA 04-114; (v) having a surface quality with no surface defects of a length greater than 0.15 mm; (vi) capable of being drawn to a diameter of 0.30 mm or less with 3 or fewer breaks per ton, and (vii) containing by weight the following elements in the proportions shown: (1) 0.78 percent or more of carbon, (2) less than 0.01 percent of aluminum, (3) 0.040 percent or less, in the aggregate, of phosphorus and sulfur, (4) 0.006 percent or less of nitrogen, and (5) not more than 0.15 percent, in the aggregate, of copper, nickel and chromium.

This grade 1080 tire bead quality rod is defined as: (i) grade 1080 tire bead quality wire rod measuring 5.5 mm or more but not more than 7.0 mm in cross-sectional diameter; (ii) with an average partial decarburization of no more than 70 microns in depth (maximum individual 200 microns); (iii) having no non-deformable inclusions greater than 20 microns and no deformable inclusions greater than 35 microns; (iv) having a carbon segregation per heat average of 3.0 or better using European Method NFA 04-114; (v) having a surface quality with no surface defects of a length greater than 0.2 mm; (vi) capable of being drawn to a diameter of 0.78 mm or larger with 0.5 or fewer breaks per ton; and (vii) containing by weight the following elements in the proportions shown: (1) 0.78 percent or more of carbon, (2) less than 0.01 percent of soluble aluminum, (3) 0.040 percent or less, in the aggregate, of phosphorus and sulfur, (4) 0.008 percent or less of nitrogen, and (5) either not more than 0.15 percent, in the aggregate, of copper, nickel and chromium (if chromium is not specified), or not more than 0.10 percent in the aggregate of copper and nickel and a chromium content of 0.24 to 0.30 percent (if chromium is specified).

For purposes of the grade 1080 tire cord quality wire rod and the grade 1080 tire bead quality wire rod, an inclusion will be considered to be deformable if its ratio of length (measured along the axis - that is, the direction of rolling - of the rod) over thickness (measured on the same inclusion in a direction perpendicular to the axis of the rod) is equal to or greater than three. The size of an inclusion for purposes of the 20 microns and 35 microns limitations is the measurement of the largest dimension observed on a longitudinal section measured in a direction perpendicular to the axis of the rod. This measurement methodology applies only to inclusions on certain grade 1080 tire cord quality wire rod and certain grade 1080 tire bead quality wire rod that are entered, or withdrawn from warehouse, for consumption on or after July 24, 2003.

The designation of the products as “tire cord quality” or “tire bead quality” indicates the acceptability of the product for use in the production of tire cord, tire bead, or wire for use in other rubber reinforcement applications such as hose wire. These quality designations are presumed to indicate that these products are being used in tire cord, tire bead, and other rubber reinforcement applications, and such merchandise intended for the tire cord, tire bead, or other rubber reinforcement applications is not included in the scope. However, should petitioners or other interested parties provide a reasonable basis to believe or suspect that there exists a pattern of importation of such products for other than those applications, end-use certification for the importation of such products may be required. Under such circumstances, only the importers of record would normally be required to certify the end use of the imported merchandise.

All products meeting the physical description of subject merchandise that are not specifically excluded are included in this scope.

The products under review are currently classifiable under subheadings 7213.91.3010, 7213.91.3090, 7213.91.4510, 7213.91.4590, 7213.91.6010, 7213.91.6090, 7213.99.0031, 7213.99.0038, 7213.99.0090, 7227.20.0010, 7227.20.0020, 7227.20.0090, 7227.20.0095, 7227.90.6051, 7227.90.6053, 7227.90.6058, and 7227.90.6059 of the HTSUS. Although the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of this proceeding is dispositive.